fix(F2): Ethernet peripheral configuration for LAN8742A

Nucleo F207ZG has a LAN8742A.

Fix stm32duino/STM32Ethernet#56

Signed-off-by: Frederic Pillon <frederic.pillon@st.com>

Author: fpistm

system/STM32F2xx/stm32f2xx_hal_conf_default.h

@@ -206,8 +206,8 @@ in voltage and temperature.*/
 
 /* Section 2: PHY configuration section */
 
-/* DP83848 PHY Address*/
-#define DP83848_PHY_ADDRESS             0x01U
+/* LAN8742A PHY Address*/
+#define LAN8742A_PHY_ADDRESS            0x00U
 /* PHY Reset delay these values are based on a 1 ms Systick interrupt*/
 #define PHY_RESET_DELAY                 0x000000FFU
 /* PHY Configuration delay */
@@ -218,39 +218,35 @@ in voltage and temperature.*/
 
 /* Section 3: Common PHY Registers */
 
-#define PHY_BCR                         ((uint16_t)0x0000)  /*!< Transceiver Basic Control Register   */
-#define PHY_BSR                         ((uint16_t)0x0001)  /*!< Transceiver Basic Status Register    */
+#define PHY_BCR                         ((uint16_t)0x00U)    /*!< Transceiver Basic Control Register   */
+#define PHY_BSR                         ((uint16_t)0x01U)    /*!< Transceiver Basic Status Register    */
 
-#define PHY_RESET                       ((uint16_t)0x8000)  /*!< PHY Reset */
-#define PHY_LOOPBACK                    ((uint16_t)0x4000)  /*!< Select loop-back mode */
-#define PHY_FULLDUPLEX_100M             ((uint16_t)0x2100)  /*!< Set the full-duplex mode at 100 Mb/s */
-#define PHY_HALFDUPLEX_100M             ((uint16_t)0x2000)  /*!< Set the half-duplex mode at 100 Mb/s */
-#define PHY_FULLDUPLEX_10M              ((uint16_t)0x0100)  /*!< Set the full-duplex mode at 10 Mb/s  */
-#define PHY_HALFDUPLEX_10M              ((uint16_t)0x0000)  /*!< Set the half-duplex mode at 10 Mb/s  */
-#define PHY_AUTONEGOTIATION             ((uint16_t)0x1000)  /*!< Enable auto-negotiation function     */
-#define PHY_RESTART_AUTONEGOTIATION     ((uint16_t)0x0200)  /*!< Restart auto-negotiation function    */
-#define PHY_POWERDOWN                   ((uint16_t)0x0800)  /*!< Select the power down mode           */
-#define PHY_ISOLATE                     ((uint16_t)0x0400)  /*!< Isolate PHY from MII                 */
+#define PHY_RESET                       ((uint16_t)0x8000U)  /*!< PHY Reset */
+#define PHY_LOOPBACK                    ((uint16_t)0x4000U)  /*!< Select loop-back mode */
+#define PHY_FULLDUPLEX_100M             ((uint16_t)0x2100U)  /*!< Set the full-duplex mode at 100 Mb/s */
+#define PHY_HALFDUPLEX_100M             ((uint16_t)0x2000U)  /*!< Set the half-duplex mode at 100 Mb/s */
+#define PHY_FULLDUPLEX_10M              ((uint16_t)0x0100U)  /*!< Set the full-duplex mode at 10 Mb/s  */
+#define PHY_HALFDUPLEX_10M              ((uint16_t)0x0000U)  /*!< Set the half-duplex mode at 10 Mb/s  */
+#define PHY_AUTONEGOTIATION             ((uint16_t)0x1000U)  /*!< Enable auto-negotiation function     */
+#define PHY_RESTART_AUTONEGOTIATION     ((uint16_t)0x0200U)  /*!< Restart auto-negotiation function    */
+#define PHY_POWERDOWN                   ((uint16_t)0x0800U)  /*!< Select the power down mode           */
+#define PHY_ISOLATE                     ((uint16_t)0x0400U)  /*!< Isolate PHY from MII                 */
 
-#define PHY_AUTONEGO_COMPLETE           ((uint16_t)0x0020)  /*!< Auto-Negotiation process completed   */
-#define PHY_LINKED_STATUS               ((uint16_t)0x0004)  /*!< Valid link established               */
-#define PHY_JABBER_DETECTION            ((uint16_t)0x0002)  /*!< Jabber condition detected            */
+#define PHY_AUTONEGO_COMPLETE           ((uint16_t)0x0020U)  /*!< Auto-Negotiation process completed   */
+#define PHY_LINKED_STATUS               ((uint16_t)0x0004U)  /*!< Valid link established               */
+#define PHY_JABBER_DETECTION            ((uint16_t)0x0002U)  /*!< Jabber condition detected            */
 
 /* Section 4: Extended PHY Registers */
 
-#define PHY_SR                          ((uint16_t)0x0010)  /*!< PHY status register Offset                      */
-#define PHY_MICR                        ((uint16_t)0x0011)  /*!< MII Interrupt Control Register                  */
-#define PHY_MISR                        ((uint16_t)0x0012)  /*!< MII Interrupt Status and Misc. Control Register */
+#define PHY_SR                          ((uint16_t)0x1FU)    /*!< PHY special control/ status register Offset     */
 
-#define PHY_LINK_STATUS                 ((uint16_t)0x0001)  /*!< PHY Link mask                                   */
-#define PHY_SPEED_STATUS                ((uint16_t)0x0002)  /*!< PHY Speed mask                                  */
-#define PHY_DUPLEX_STATUS               ((uint16_t)0x0004)  /*!< PHY Duplex mask                                 */
+#define PHY_SPEED_STATUS                ((uint16_t)0x0004U)  /*!< PHY Speed mask                                  */
+#define PHY_DUPLEX_STATUS               ((uint16_t)0x0010U)  /*!< PHY Duplex mask                                 */
 
-#define PHY_MICR_INT_EN                 ((uint16_t)0x0002)  /*!< PHY Enable interrupts                           */
-#define PHY_MICR_INT_OE                 ((uint16_t)0x0001)  /*!< PHY Enable output interrupt events              */
 
-#define PHY_MISR_LINK_INT_EN            ((uint16_t)0x0020)  /*!< Enable Interrupt on change of link status       */
-#define PHY_LINK_INTERRUPT              ((uint16_t)0x2000)  /*!< PHY link status interrupt mask                  */
+#define PHY_ISFR                        ((uint16_t)0x01DU)   /*!< PHY Interrupt Source Flag register Offset       */
+#define PHY_IMR                         ((uint16_t)0x001E)   /*!< PHY Interrupt Mask register Offset              */
+#define PHY_ISFR_INT4                   ((uint16_t)0x0010U)  /*!< PHY Link down inturrupt                         */
 
 /* ################## SPI peripheral configuration ########################## */