system(H7): Update the system source file

Signed-off-by: Alexandre Bourdiol <alexandre.bourdiol@st.com>

Author: ABOSTM

system/STM32H7xx/stm32h7xx_hal_conf_default.h

@@ -5,13 +5,12 @@
   ******************************************************************************
   * @attention
   *
-  * <h2><center>&copy; Copyright (c) 2017 STMicroelectronics.
-  * All rights reserved.</center></h2>
+  * Copyright (c) 2017 STMicroelectronics.
+  * All rights reserved.
   *
-  * This software component is licensed by ST under BSD 3-Clause license,
-  * the "License"; You may not use this file except in compliance with the
-  * License. You may obtain a copy of the License at:
-  *                        opensource.org/licenses/BSD-3-Clause
+  * This software is licensed under terms that can be found in the LICENSE file
+  * in the root directory of this software component.
+  * If no LICENSE file comes with this software, it is provided AS-IS.
   *
   ******************************************************************************
   */
@@ -521,6 +520,3 @@ void assert_failed(uint8_t *file, uint32_t line);
 #endif
 
 #endif /* __STM32H7xx_HAL_CONF_DEFAULT_H */
-
-
-/************************ (C) COPYRIGHT STMicroelectronics *****END OF FILE****/

system/STM32H7xx/system_stm32h7xx.c

@@ -22,13 +22,12 @@
   ******************************************************************************
   * @attention
   *
-  * <h2><center>&copy; Copyright (c) 2017 STMicroelectronics.
-  * All rights reserved.</center></h2>
+  * Copyright (c) 2017 STMicroelectronics.
+  * All rights reserved.
   *
-  * This software component is licensed by ST under BSD 3-Clause license,
-  * the "License"; You may not use this file except in compliance with the
-  * License. You may obtain a copy of the License at:
-  *                        opensource.org/licenses/BSD-3-Clause
+  * This software is licensed under terms that can be found in the LICENSE file
+  * in the root directory of this software component.
+  * If no LICENSE file comes with this software, it is provided AS-IS.
   *
   ******************************************************************************
   */
@@ -74,7 +73,45 @@
 #ifndef VECT_TAB_OFFSET
 #define VECT_TAB_OFFSET  0x00000000UL /*!< Vector Table base offset field.
                                       This value must be a multiple of 0x200. */
+#else
+
+#define USER_VECT_TAB_ADDRESS
+
 #endif
+
+/* Note: Following vector table addresses must be defined in line with linker
+         configuration. */
+/*!< Define USER_VECT_TAB_ADDRESS if you need to relocate the vector table
+
+     anywhere in Flash or Sram, else the vector table is kept at the automatic
+
+     remap of boot address selected */
+#if defined(USER_VECT_TAB_ADDRESS)
+#if defined(DUAL_CORE) && defined(CORE_CM4)
+/*!< Define VECT_TAB_SRAM if you need to relocate your vector Table
+
+     in Sram else user remap will be done in Flash. */
+#if defined(VECT_TAB_SRAM)
+#define VECT_TAB_BASE_ADDRESS   D2_AXISRAM_BASE   /*!< Vector Table base address field.
+                                                       This value must be a multiple of 0x200. */
+#else
+#define VECT_TAB_BASE_ADDRESS   FLASH_BANK2_BASE  /*!< Vector Table base address field.
+                                                       This value must be a multiple of 0x200. */
+#endif /* VECT_TAB_SRAM */
+#else
+/*!< Define VECT_TAB_SRAM if you need to relocate your vector Table
+
+     in Sram else user remap will be done in Flash. */
+#if defined(VECT_TAB_SRAM)
+#define VECT_TAB_BASE_ADDRESS   D1_AXISRAM_BASE   /*!< Vector Table base address field.
+                                                       This value must be a multiple of 0x200. */
+#else
+#define VECT_TAB_BASE_ADDRESS   FLASH_BANK1_BASE  /*!< Vector Table base address field.
+                                                       This value must be a multiple of 0x200. */
+#endif /* VECT_TAB_SRAM */
+#endif /* DUAL_CORE && CORE_CM4 */
+#endif /* USER_VECT_TAB_ADDRESS */
+
 /******************************************************************************/
 
 /**
@@ -235,11 +272,9 @@ void SystemInit (void)
 
 #if defined(DUAL_CORE) && defined(CORE_CM4)
   /* Configure the Vector Table location add offset address for cortex-M4 ------------------*/
-#ifdef VECT_TAB_SRAM
-  SCB->VTOR = D2_AXISRAM_BASE | VECT_TAB_OFFSET; /* Vector Table Relocation in Internal SRAM */
-#else
-  SCB->VTOR = FLASH_BANK2_BASE | VECT_TAB_OFFSET; /* Vector Table Relocation in Internal FLASH */
-#endif /* VECT_TAB_SRAM */
+#if defined(USER_VECT_TAB_ADDRESS)
+  SCB->VTOR = VECT_TAB_BASE_ADDRESS | VECT_TAB_OFFSET; /* Vector Table Relocation in Internal D2 AXI-RAM or in Internal FLASH */
+#endif /* USER_VECT_TAB_ADDRESS */
 
 #else
 
@@ -251,11 +286,9 @@ void SystemInit (void)
   FMC_Bank1_R->BTCR[0] = 0x000030D2;
 
   /* Configure the Vector Table location add offset address for cortex-M7 ------------------*/
-#ifdef VECT_TAB_SRAM
-  SCB->VTOR = D1_AXISRAM_BASE  | VECT_TAB_OFFSET; /* Vector Table Relocation in Internal AXI-RAM */
-#else
-  SCB->VTOR = FLASH_BANK1_BASE | VECT_TAB_OFFSET;       /* Vector Table Relocation in Internal FLASH */
-#endif
+#if defined(USER_VECT_TAB_ADDRESS)
+  SCB->VTOR = VECT_TAB_BASE_ADDRESS | VECT_TAB_OFFSET; /* Vector Table Relocation in Internal D1 AXI-RAM or in Internal FLASH */
+#endif /* USER_VECT_TAB_ADDRESS */
 
 #endif /*DUAL_CORE && CORE_CM4*/
 
@@ -407,4 +440,3 @@ void SystemCoreClockUpdate (void)
 /**
   * @}
   */
-/************************ (C) COPYRIGHT STMicroelectronics *****END OF FILE****/