Avoid use of stm32_hal_legacy definition

If required defined: USE_HAL_LEGACY

Signed-off-by: Frederic.Pillon <frederic.pillon@st.com>

Author: fpistm

cores/arduino/stm32/PortNames.c

@@ -100,64 +100,64 @@ GPIO_TypeDef *set_GPIO_Port_Clock(uint32_t port_idx) {
     switch (port_idx) {
         case PortA:
             gpioPort = GPIOA_BASE;
-            __GPIOA_CLK_ENABLE();
+            __HAL_RCC_GPIOA_CLK_ENABLE();
             break;
         case PortB:
             gpioPort = GPIOB_BASE;
-            __GPIOB_CLK_ENABLE();
+            __HAL_RCC_GPIOB_CLK_ENABLE();
             break;
 #if defined GPIOC_BASE
         case PortC:
             gpioPort = GPIOC_BASE;
-            __GPIOC_CLK_ENABLE();
+            __HAL_RCC_GPIOC_CLK_ENABLE();
             break;
 #endif
 #if defined GPIOD_BASE
         case PortD:
             gpioPort = GPIOD_BASE;
-            __GPIOD_CLK_ENABLE();
+            __HAL_RCC_GPIOD_CLK_ENABLE();
             break;
 #endif
 #if defined GPIOE_BASE
         case PortE:
             gpioPort = GPIOE_BASE;
-            __GPIOE_CLK_ENABLE();
+            __HAL_RCC_GPIOE_CLK_ENABLE();
             break;
 #endif
 #if defined GPIOF_BASE
         case PortF:
             gpioPort = GPIOF_BASE;
-            __GPIOF_CLK_ENABLE();
+            __HAL_RCC_GPIOF_CLK_ENABLE();
             break;
 #endif
 #if defined GPIOG_BASE
         case PortG:
             gpioPort = GPIOG_BASE;
-            __GPIOG_CLK_ENABLE();
+            __HAL_RCC_GPIOG_CLK_ENABLE();
             break;
 #endif
 #if defined GPIOH_BASE
         case PortH:
             gpioPort = GPIOH_BASE;
-            __GPIOH_CLK_ENABLE();
+            __HAL_RCC_GPIOH_CLK_ENABLE();
             break;
 #endif
 #if defined GPIOI_BASE
         case PortI:
             gpioPort = GPIOI_BASE;
-            __GPIOI_CLK_ENABLE();
+            __HAL_RCC_GPIOI_CLK_ENABLE();
             break;
 #endif
 #if defined GPIOJ_BASE
         case PortJ:
             gpioPort = GPIOJ_BASE;
-            __GPIOJ_CLK_ENABLE();
+            __HAL_RCC_GPIOJ_CLK_ENABLE();
             break;
 #endif
 #if defined GPIOK_BASE
         case PortK:
             gpioPort = GPIOK_BASE;
-            __GPIOK_CLK_ENABLE();
+            __HAL_RCC_GPIOK_CLK_ENABLE();
             break;
 #endif
         default:

cores/arduino/stm32/spi_com.c

@@ -252,7 +252,7 @@ void spi_init(spi_t *obj, uint32_t speed, spi_mode_e mode, uint8_t msb)
     handle->Init.CLKPolarity       = SPI_POLARITY_HIGH;
   }
 
-  handle->Init.CRCCalculation    = SPI_CRCCALCULATION_DISABLED;
+  handle->Init.CRCCalculation    = SPI_CRCCALCULATION_DISABLE;
   handle->Init.CRCPolynomial     = 7;
   handle->Init.DataSize          = SPI_DATASIZE_8BIT;
 
@@ -262,7 +262,7 @@ void spi_init(spi_t *obj, uint32_t speed, spi_mode_e mode, uint8_t msb)
     handle->Init.FirstBit          = SPI_FIRSTBIT_MSB;
   }
 
-  handle->Init.TIMode            = SPI_TIMODE_DISABLED;
+  handle->Init.TIMode            = SPI_TIMODE_DISABLE;
 
   if(obj->pin_mosi != NC) {
     port = set_GPIO_Port_Clock(STM_PORT(obj->pin_mosi));

cores/arduino/stm32/twi.c

@@ -235,9 +235,9 @@ void i2c_custom_init(i2c_t *obj, i2c_timing_e timing, uint32_t addressingMode, u
   handle->Init.OwnAddress1     = ownAddress;
   handle->Init.OwnAddress2     = 0xFF;
   handle->Init.AddressingMode  = addressingMode;
-  handle->Init.DualAddressMode = I2C_DUALADDRESS_DISABLED;
-  handle->Init.GeneralCallMode = I2C_GENERALCALL_DISABLED;
-  handle->Init.NoStretchMode   = I2C_NOSTRETCH_DISABLED;
+  handle->Init.DualAddressMode = I2C_DUALADDRESS_DISABLE;
+  handle->Init.GeneralCallMode = I2C_GENERALCALL_DISABLE;
+  handle->Init.NoStretchMode   = I2C_NOSTRETCH_DISABLE;
 
   if(master == 0) {
     HAL_NVIC_SetPriority(obj->irq, 0, 1);