Merge tag 'iio-fixes-for-6.8a' of http://git.kernel.org/pub/scm/linux/kernel/git/jic23/iio into char-misc-linus

gregkh · gregkh · commit 23d62fb5d368 · 2024-02-14T16:19:17.000+01:00
Jonathan writes: IIO: 1st set of fixes for the 6.8 cycle Usual mixed bag of issues introduced this cycle and fixes for long term issues that have been identified recently + one case where I messed up a merge resolution and dropped the build file changes. Most important is the userspace ABI fix for the iio_modifier enum where we accidentally added new entries in the middle rather than at the end. IIO Core - Close a memory leak in an error path. - Move LIGHT_UVA and LIGHT_UVB definitions to end of the iio_modifier enum to avoid breaking older userspace. (not yet in a released kernel thankfully). adi,adis - Fix a DMA buffer alignment issue that was missing in series that fixed these across IIO. adi,ad-sigma-delta - Fix a DMA buffer alignment issue that was missing in series that fixed these across IIO. adi,ad4130 - Zero init remaining fields of clock init data. - Only set GPIO control bits on pins that aren't in use for anything else. adi,ad5933 - Fix an old bug due to type mismatch. This is a rare device so good to get some new test coverage. adi,ad7091r - Use right variable for an error return code. bosch,bma400 - Add missing CONFIG_REGMAP_I2C dependency. bosch,bmp280: - Add missing bmp085 ID to the SPI table to avoid mismatch with the of_device_id table. hid-sensors: - Avoid returning an error for timestamp read back that succeeds. pni,rm3100 - Check value read from RM31000_REG_TMRC register is valid before using it. Hardening to avoid a real world issue seen on some faulty hardware. st,st-sensors - Fix a DMA buffer alignment issue that was missing in series that fixed these across IIO. ti,hdc3020 - Add missing Kconfig and Makefile entrees accidentally dropped when patches were applied. - Fix wrong temperature offset (negated) * tag 'iio-fixes-for-6.8a' of http://git.kernel.org/pub/scm/linux/kernel/git/jic23/iio: iio: adc: ad4130: only set GPIO_CTRL if pin is unused iio: adc: ad4130: zero-initialize clock init data iio: accel: bma400: Fix a compilation problem iio: commom: st_sensors: ensure proper DMA alignment iio: hid-sensor-als: Return 0 for HID_USAGE_SENSOR_TIME_TIMESTAMP iio: move LIGHT_UVA and LIGHT_UVB to the end of iio_modifier staging: iio: ad5933: fix type mismatch regression iio: humidity: hdc3020: fix temperature offset iio: adc: ad7091r8: Fix error code in ad7091r8_gpio_setup() iio: adc: ad_sigma_delta: ensure proper DMA alignment iio: imu: adis: ensure proper DMA alignment iio: humidity: hdc3020: Add Makefile, Kconfig and MAINTAINERS entry iio: imu: bno055: serdev requires REGMAP iio: magnetometer: rm3100: add boundary check for the value read from RM3100_REG_TMRC iio: pressure: bmp280: Add missing bmp085 to SPI id table iio: core: fix memleak in iio_device_register_sysfs
diff --git a/MAINTAINERS b/MAINTAINERS
@@ -22010,6 +22010,14 @@ F:	Documentation/devicetree/bindings/media/i2c/ti,ds90*
 F:	drivers/media/i2c/ds90*
 F:	include/media/i2c/ds90*
 
+TI HDC302X HUMIDITY DRIVER
+M:	Javier Carrasco <javier.carrasco.cruz@gmail.com>
+M:	Li peiyu <579lpy@gmail.com>
+L:	linux-iio@vger.kernel.org
+S:	Maintained
+F:	Documentation/devicetree/bindings/iio/humidity/ti,hdc3020.yaml
+F:	drivers/iio/humidity/hdc3020.c
+
 TI ICSSG ETHERNET DRIVER (ICSSG)
 R:	MD Danish Anwar <danishanwar@ti.com>
 R:	Roger Quadros <rogerq@kernel.org>
diff --git a/drivers/iio/accel/Kconfig b/drivers/iio/accel/Kconfig
@@ -219,10 +219,12 @@ config BMA400
 
 config BMA400_I2C
 	tristate
+	select REGMAP_I2C
 	depends on BMA400
 
 config BMA400_SPI
 	tristate
+	select REGMAP_SPI
 	depends on BMA400
 
 config BMC150_ACCEL
diff --git a/drivers/iio/adc/ad4130.c b/drivers/iio/adc/ad4130.c
@@ -1821,7 +1821,7 @@ static int ad4130_setup_int_clk(struct ad4130_state *st)
 {
 	struct device *dev = &st->spi->dev;
 	struct device_node *of_node = dev_of_node(dev);
-	struct clk_init_data init;
+	struct clk_init_data init = {};
 	const char *clk_name;
 	int ret;
 
@@ -1891,10 +1891,14 @@ static int ad4130_setup(struct iio_dev *indio_dev)
 		return ret;
 
 	/*
-	 * Configure all GPIOs for output. If configured, the interrupt function
-	 * of P2 takes priority over the GPIO out function.
+	 * Configure unused GPIOs for output. If configured, the interrupt
+	 * function of P2 takes priority over the GPIO out function.
 	 */
-	val =  AD4130_IO_CONTROL_GPIO_CTRL_MASK;
+	val = 0;
+	for (i = 0; i < AD4130_MAX_GPIOS; i++)
+		if (st->pins_fn[i + AD4130_AIN2_P1] == AD4130_PIN_FN_NONE)
+			val |= FIELD_PREP(AD4130_IO_CONTROL_GPIO_CTRL_MASK, BIT(i));
+
 	val |= FIELD_PREP(AD4130_IO_CONTROL_INT_PIN_SEL_MASK, st->int_pin_sel);
 
 	ret = regmap_write(st->regmap, AD4130_IO_CONTROL_REG, val);
diff --git a/drivers/iio/adc/ad7091r8.c b/drivers/iio/adc/ad7091r8.c
@@ -195,7 +195,7 @@ static int ad7091r8_gpio_setup(struct ad7091r_state *st)
 	st->reset_gpio = devm_gpiod_get_optional(st->dev, "reset",
 						 GPIOD_OUT_HIGH);
 	if (IS_ERR(st->reset_gpio))
-		return dev_err_probe(st->dev, PTR_ERR(st->convst_gpio),
+		return dev_err_probe(st->dev, PTR_ERR(st->reset_gpio),
 				     "Error on requesting reset GPIO\n");
 
 	if (st->reset_gpio) {
diff --git a/drivers/iio/humidity/Kconfig b/drivers/iio/humidity/Kconfig
@@ -48,6 +48,18 @@ config HDC2010
 	  To compile this driver as a module, choose M here: the module
 	  will be called hdc2010.
 
+config HDC3020
+	tristate "TI HDC3020 relative humidity and temperature sensor"
+	depends on I2C
+	select CRC8
+	help
+	  Say yes here to build support for the Texas Instruments
+	  HDC3020, HDC3021 and HDC3022 relative humidity and temperature
+	  sensors.
+
+	  To compile this driver as a module, choose M here: the module
+	  will be called hdc3020.
+
 config HID_SENSOR_HUMIDITY
 	tristate "HID Environmental humidity sensor"
 	depends on HID_SENSOR_HUB
diff --git a/drivers/iio/humidity/Makefile b/drivers/iio/humidity/Makefile
@@ -7,6 +7,7 @@ obj-$(CONFIG_AM2315) += am2315.o
 obj-$(CONFIG_DHT11) += dht11.o
 obj-$(CONFIG_HDC100X) += hdc100x.o
 obj-$(CONFIG_HDC2010) += hdc2010.o
+obj-$(CONFIG_HDC3020) += hdc3020.o
 obj-$(CONFIG_HID_SENSOR_HUMIDITY) += hid-sensor-humidity.o
 
 hts221-y := hts221_core.o \
diff --git a/drivers/iio/humidity/hdc3020.c b/drivers/iio/humidity/hdc3020.c
@@ -322,7 +322,7 @@ static int hdc3020_read_raw(struct iio_dev *indio_dev,
 		if (chan->type != IIO_TEMP)
 			return -EINVAL;
 
-		*val = 16852;
+		*val = -16852;
 		return IIO_VAL_INT;
 
 	default:
diff --git a/drivers/iio/imu/bno055/Kconfig b/drivers/iio/imu/bno055/Kconfig
@@ -8,6 +8,7 @@ config BOSCH_BNO055
 config BOSCH_BNO055_SERIAL
 	tristate "Bosch BNO055 attached via UART"
 	depends on SERIAL_DEV_BUS
+	select REGMAP
 	select BOSCH_BNO055
 	help
 	  Enable this to support Bosch BNO055 IMUs attached via UART.
diff --git a/drivers/iio/industrialio-core.c b/drivers/iio/industrialio-core.c
@@ -1584,10 +1584,13 @@ static int iio_device_register_sysfs(struct iio_dev *indio_dev)
 	ret = iio_device_register_sysfs_group(indio_dev,
 					      &iio_dev_opaque->chan_attr_group);
 	if (ret)
-		goto error_clear_attrs;
+		goto error_free_chan_attrs;
 
 	return 0;
 
+error_free_chan_attrs:
+	kfree(iio_dev_opaque->chan_attr_group.attrs);
+	iio_dev_opaque->chan_attr_group.attrs = NULL;
 error_clear_attrs:
 	iio_free_chan_devattr_list(&iio_dev_opaque->channel_attr_list);
 
diff --git a/drivers/iio/light/hid-sensor-als.c b/drivers/iio/light/hid-sensor-als.c
@@ -226,6 +226,7 @@ static int als_capture_sample(struct hid_sensor_hub_device *hsdev,
 	case HID_USAGE_SENSOR_TIME_TIMESTAMP:
 		als_state->timestamp = hid_sensor_convert_timestamp(&als_state->common_attributes,
 								    *(s64 *)raw_data);
+		ret = 0;
 		break;
 	default:
 		break;
diff --git a/drivers/iio/magnetometer/rm3100-core.c b/drivers/iio/magnetometer/rm3100-core.c
@@ -530,6 +530,7 @@ int rm3100_common_probe(struct device *dev, struct regmap *regmap, int irq)
 	struct rm3100_data *data;
 	unsigned int tmp;
 	int ret;
+	int samp_rate_index;
 
 	indio_dev = devm_iio_device_alloc(dev, sizeof(*data));
 	if (!indio_dev)
@@ -586,9 +587,14 @@ int rm3100_common_probe(struct device *dev, struct regmap *regmap, int irq)
 	ret = regmap_read(regmap, RM3100_REG_TMRC, &tmp);
 	if (ret < 0)
 		return ret;
+
+	samp_rate_index = tmp - RM3100_TMRC_OFFSET;
+	if (samp_rate_index < 0 || samp_rate_index >=  RM3100_SAMP_NUM) {
+		dev_err(dev, "The value read from RM3100_REG_TMRC is invalid!\n");
+		return -EINVAL;
+	}
 	/* Initializing max wait time, which is double conversion time. */
-	data->conversion_time = rm3100_samp_rates[tmp - RM3100_TMRC_OFFSET][2]
-				* 2;
+	data->conversion_time = rm3100_samp_rates[samp_rate_index][2] * 2;
 
 	/* Cycle count values may not be what we want. */
 	if ((tmp - RM3100_TMRC_OFFSET) == 0)
diff --git a/drivers/iio/pressure/bmp280-spi.c b/drivers/iio/pressure/bmp280-spi.c
@@ -87,6 +87,7 @@ static const struct of_device_id bmp280_of_spi_match[] = {
 MODULE_DEVICE_TABLE(of, bmp280_of_spi_match);
 
 static const struct spi_device_id bmp280_spi_id[] = {
+	{ "bmp085", (kernel_ulong_t)&bmp180_chip_info },
 	{ "bmp180", (kernel_ulong_t)&bmp180_chip_info },
 	{ "bmp181", (kernel_ulong_t)&bmp180_chip_info },
 	{ "bmp280", (kernel_ulong_t)&bmp280_chip_info },
diff --git a/drivers/staging/iio/impedance-analyzer/ad5933.c b/drivers/staging/iio/impedance-analyzer/ad5933.c
@@ -608,7 +608,7 @@ static void ad5933_work(struct work_struct *work)
 		struct ad5933_state, work.work);
 	struct iio_dev *indio_dev = i2c_get_clientdata(st->client);
 	__be16 buf[2];
-	int val[2];
+	u16 val[2];
 	unsigned char status;
 	int ret;
 
diff --git a/include/linux/iio/adc/ad_sigma_delta.h b/include/linux/iio/adc/ad_sigma_delta.h
@@ -8,6 +8,8 @@
 #ifndef __AD_SIGMA_DELTA_H__
 #define __AD_SIGMA_DELTA_H__
 
+#include <linux/iio/iio.h>
+
 enum ad_sigma_delta_mode {
 	AD_SD_MODE_CONTINUOUS = 0,
 	AD_SD_MODE_SINGLE = 1,
@@ -99,7 +101,7 @@ struct ad_sigma_delta {
 	 * 'rx_buf' is up to 32 bits per sample + 64 bit timestamp,
 	 * rounded to 16 bytes to take into account padding.
 	 */
-	uint8_t				tx_buf[4] ____cacheline_aligned;
+	uint8_t				tx_buf[4] __aligned(IIO_DMA_MINALIGN);
 	uint8_t				rx_buf[16] __aligned(8);
 };
 
diff --git a/include/linux/iio/common/st_sensors.h b/include/linux/iio/common/st_sensors.h
@@ -258,9 +258,9 @@ struct st_sensor_data {
 	bool hw_irq_trigger;
 	s64 hw_timestamp;
 
-	char buffer_data[ST_SENSORS_MAX_BUFFER_SIZE] ____cacheline_aligned;
-
 	struct mutex odr_lock;
+
+	char buffer_data[ST_SENSORS_MAX_BUFFER_SIZE] __aligned(IIO_DMA_MINALIGN);
 };
 
 #ifdef CONFIG_IIO_BUFFER
diff --git a/include/linux/iio/imu/adis.h b/include/linux/iio/imu/adis.h
@@ -11,6 +11,7 @@
 
 #include <linux/spi/spi.h>
 #include <linux/interrupt.h>
+#include <linux/iio/iio.h>
 #include <linux/iio/types.h>
 
 #define ADIS_WRITE_REG(reg) ((0x80 | (reg)))
@@ -131,7 +132,7 @@ struct adis {
 	unsigned long		irq_flag;
 	void			*buffer;
 
-	u8			tx[10] ____cacheline_aligned;
+	u8			tx[10] __aligned(IIO_DMA_MINALIGN);
 	u8			rx[4];
 };
 
diff --git a/include/uapi/linux/iio/types.h b/include/uapi/linux/iio/types.h
@@ -91,8 +91,6 @@ enum iio_modifier {
 	IIO_MOD_CO2,
 	IIO_MOD_VOC,
 	IIO_MOD_LIGHT_UV,
-	IIO_MOD_LIGHT_UVA,
-	IIO_MOD_LIGHT_UVB,
 	IIO_MOD_LIGHT_DUV,
 	IIO_MOD_PM1,
 	IIO_MOD_PM2P5,
@@ -107,6 +105,8 @@ enum iio_modifier {
 	IIO_MOD_PITCH,
 	IIO_MOD_YAW,
 	IIO_MOD_ROLL,
+	IIO_MOD_LIGHT_UVA,
+	IIO_MOD_LIGHT_UVB,
 };
 
 enum iio_event_type {
