Replace periph_ctrl.h use because of deprecation

Author: me-no-dev

cores/esp32/esp32-hal-i2c-slave.c

@@ -36,10 +36,10 @@
 #include "freertos/ringbuf.h"
 
 #include "esp_intr_alloc.h"
-#include "driver/periph_ctrl.h"
 #include "soc/i2c_reg.h"
 #include "soc/i2c_struct.h"
 #include "hal/i2c_ll.h"
+#include "hal/clk_gate_ll.h"
 #include "esp32-hal-log.h"
 #include "esp32-hal-i2c-slave.h"
 
@@ -292,10 +292,10 @@ esp_err_t i2cSlaveInit(uint8_t num, int sda, int scl, uint16_t slaveID, uint32_t
     frequency = (frequency * 5) / 4;
 
     if (i2c->num == 0) {
-        periph_module_enable(PERIPH_I2C0_MODULE);
+        periph_ll_enable_clk_clear_rst(PERIPH_I2C0_MODULE);
 #if SOC_I2C_NUM > 1
     } else {
-        periph_module_enable(PERIPH_I2C1_MODULE);
+        periph_ll_enable_clk_clear_rst(PERIPH_I2C1_MODULE);
 #endif
     }
 

cores/esp32/esp32-hal-spi.c

@@ -23,7 +23,7 @@
 #include "soc/io_mux_reg.h"
 #include "soc/gpio_sig_map.h"
 #include "soc/rtc.h"
-#include "driver/periph_ctrl.h"
+#include "hal/clk_gate_ll.h"
 
 #include "esp_system.h"
 #ifdef ESP_IDF_VERSION_MAJOR // IDF 4+
@@ -729,11 +729,11 @@ spi_t * spiStartBus(uint8_t spi_num, uint32_t clockDiv, uint8_t dataMode, uint8_
     }
 #elif CONFIG_IDF_TARGET_ESP32S3
     if(spi_num == FSPI) {
-        periph_module_reset( PERIPH_SPI2_MODULE );
-        periph_module_enable( PERIPH_SPI2_MODULE );
+        periph_ll_reset( PERIPH_SPI2_MODULE );
+        periph_ll_enable_clk_clear_rst( PERIPH_SPI2_MODULE );
     } else if(spi_num == HSPI) {
-        periph_module_reset( PERIPH_SPI3_MODULE );
-        periph_module_enable( PERIPH_SPI3_MODULE );
+        periph_ll_reset( PERIPH_SPI3_MODULE );
+        periph_ll_enable_clk_clear_rst( PERIPH_SPI3_MODULE );
     }
 #elif CONFIG_IDF_TARGET_ESP32
     if(spi_num == HSPI) {
@@ -747,8 +747,8 @@ spi_t * spiStartBus(uint8_t spi_num, uint32_t clockDiv, uint8_t dataMode, uint8_
         DPORT_CLEAR_PERI_REG_MASK(DPORT_PERIP_RST_EN_REG, DPORT_SPI01_RST);
     }
 #elif CONFIG_IDF_TARGET_ESP32C3
-    periph_module_reset( PERIPH_SPI2_MODULE );
-    periph_module_enable( PERIPH_SPI2_MODULE );
+    periph_ll_reset( PERIPH_SPI2_MODULE );
+    periph_ll_enable_clk_clear_rst( PERIPH_SPI2_MODULE );
 #endif
 
     SPI_MUTEX_LOCK();

cores/esp32/esp32-hal-tinyusb.c

@@ -22,12 +22,12 @@
 
 #include "hal/usb_hal.h"
 #include "hal/gpio_ll.h"
+#include "hal/clk_gate_ll.h"
 
 #include "freertos/FreeRTOS.h"
 #include "freertos/task.h"
 
 #include "driver/gpio.h"
-#include "driver/periph_ctrl.h"
 
 #include "esp_rom_gpio.h"
 
@@ -395,9 +395,9 @@ static void hw_cdc_reset_handler(void *arg) {
 
 static void usb_switch_to_cdc_jtag(){
     // Disable USB-OTG
-    periph_module_reset(PERIPH_USB_MODULE);
-    //periph_module_enable(PERIPH_USB_MODULE);
-    periph_module_disable(PERIPH_USB_MODULE);
+    periph_ll_reset(PERIPH_USB_MODULE);
+    //periph_ll_enable_clk_clear_rst(PERIPH_USB_MODULE);
+    periph_ll_disable_clk_set_rst(PERIPH_USB_MODULE);
 
     // Switch to hardware CDC+JTAG
     CLEAR_PERI_REG_MASK(RTC_CNTL_USB_CONF_REG, (RTC_CNTL_SW_HW_USB_PHY_SEL|RTC_CNTL_SW_USB_PHY_SEL|RTC_CNTL_USB_PAD_ENABLE));
@@ -457,8 +457,8 @@ static void IRAM_ATTR usb_persist_shutdown_handler(void)
                 chip_usb_set_persist_flags(USBDC_PERSIST_ENA);
 #if CONFIG_IDF_TARGET_ESP32S2
             } else {
-                periph_module_reset(PERIPH_USB_MODULE);
-                periph_module_enable(PERIPH_USB_MODULE);
+                periph_ll_reset(PERIPH_USB_MODULE);
+                periph_ll_enable_clk_clear_rst(PERIPH_USB_MODULE);
 #endif
             }
             REG_WRITE(RTC_CNTL_OPTION1_REG, RTC_CNTL_FORCE_DOWNLOAD_BOOT);
@@ -696,8 +696,8 @@ esp_err_t tinyusb_init(tinyusb_device_config_t *config) {
     //} else 
     if(!usb_did_persist || !usb_persist_enabled){
         // Reset USB module
-        periph_module_reset(PERIPH_USB_MODULE);
-        periph_module_enable(PERIPH_USB_MODULE);
+        periph_ll_reset(PERIPH_USB_MODULE);
+        periph_ll_enable_clk_clear_rst(PERIPH_USB_MODULE);
     }
 
     tinyusb_config_t tusb_cfg = {