5V changes and family

Author: pedromsousalima

content/hardware/11.accessories/family.md

@@ -1,6 +1,6 @@
 ---
-title: Mega
-description: The largest Arduino form factor with a lot of GPIOs.
+title: Accessories
+description: To make your projects even greater.
 businessUnit: maker
-anchor: mega-family
+anchor: accessories-family
 ---

content/hardware/11.accessories/modulinos/modulino-buttons/tutorials/how-buttons-ardu/how-to-buttons-ardu.md

@@ -69,11 +69,11 @@ The pinout for the Modulino Buttons is shown below. While the recommended connec
 
 ## Power Specifications
 
-The board is typically powered by +3.3 VDC when using the QWIIC interface as per the I²C standard. However, different power levels can be used when powering through the solderable pins, making this board compatible with both +3.3 and +5 VDC.
+The board is typically powered by +3.3 VDC when using the QWIIC interface as per the I²C standard.
 
 | Parameter        | Condition         | Minimum | Typical     | Maximum | Unit |
 |------------------|-------------------|---------|-------------|---------|------|
-| Supply Voltage   | -                 | 2.3     | 3.3 (QWIIC) | 5.5     | V    |
+| Supply Voltage   | -                 | 2.3     | 3.3 (QWIIC) | 3.6     | V    |
 | LED Current Draw | Single LED Active | -       | 2.5         | -       | mA   |
 
 The module includes a power LED that draws 1 mA and turns on as soon as it is powered. J1 (Qwiic connector), J2 (Qwiic connector), and the headers all share the same power branch. The power distribution of the module is therefore as follows:

content/hardware/11.accessories/modulinos/modulino-buttons/tutorials/how-buttons-mp/how-to-buttons-mp.md

@@ -69,11 +69,11 @@ The pinout for the Modulino Buttons is shown below. While the recommended connec
 
 ## Power Specifications
 
-The board is typically powered by +3.3 VDC when using the QWIIC interface as per the I²C standard. However, different power levels can be used when powering through the solderable pins, making this board compatible with both +3.3 and +5 VDC.
+The board is typically powered by +3.3 VDC when using the QWIIC interface as per the I²C standard.
 
 | Parameter        | Condition         | Minimum | Typical     | Maximum | Unit |
 |------------------|-------------------|---------|-------------|---------|------|
-| Supply Voltage   | -                 | 2.3     | 3.3 (QWIIC) | 5.5     | V    |
+| Supply Voltage   | -                 | 2.3     | 3.3 (QWIIC) | 3.6     | V    |
 | LED Current Draw | Single LED Active | -       | 2.5         | -       | mA   |
 
 The module includes a power LED that draws 1 mA and turns on as soon as it is powered. J1 (Qwiic connector), J2 (Qwiic connector), and the headers all share the same power branch. The power distribution of the module is therefore as follows:

content/hardware/11.accessories/modulinos/modulino-buzzer/tutorials/how-buzzer-ardu/content.md

@@ -84,7 +84,7 @@ The board is typically powered by +3.3 VDC when using the QWIIC interface as per
 
 | Parameter           | Condition       | Minimum | Typical | Maximum | Unit |
 |---------------------|-----------------|---------|---------|---------|------|
-| Operating Voltage   | -               | 2.5     | 3.3     | 5.5     | V    |
+| Operating Voltage   | -               | 2.5     | 3.3     | 3.6     | V    |
 | Current Consumption | @ 3.3V, 2.7 kHz | -       | 120     | -       | μA   |
 
 The module includes a power LED that draws 1 mA and turns on as soon as it is powered.

content/hardware/11.accessories/modulinos/modulino-buzzer/tutorials/how-buzzer-mp/content.md

@@ -83,7 +83,7 @@ The board is typically powered by +3.3 VDC when using the QWIIC interface as per
 
 | Parameter           | Condition       | Minimum | Typical | Maximum | Unit |
 |---------------------|-----------------|---------|---------|---------|------|
-| Operating Voltage   | -               | 2.5     | 3.3     | 5.5     | V    |
+| Operating Voltage   | -               | 2.5     | 3.3     | 3.6     | V    |
 | Current Consumption | @ 3.3V, 2.7 kHz | -       | 120     | -       | μA   |
 
 The module includes a power LED that draws 1 mA and turns on as soon as it is powered.

content/hardware/11.accessories/modulinos/modulino-pixels/tutorials/how-pixels-ardu/content.md

@@ -74,11 +74,11 @@ Later in this article we teach how to [change the address](#how-to-change-i2c-ad
 
 ## Power Specifications
 
-The board is typically powered by +3.3 VDC when using the QWIIC interface as per the I²C standard. However, different power levels can be used when powering through the solderable pins, making this board compatible with both +3.3 and +5 VDC.
+The board is typically powered by +3.3 VDC when using the QWIIC interface as per the I²C standard.
 
 | Parameter              | Condition      | Minimum | Typical | Maximum | Unit |
 |------------------------|----------------|---------|---------|---------|------|
-| Operating Voltage      | -              | 4.5     | 3.3     | 5.5     | V    |
+| Operating Voltage      | -              | 4.5     | 3.3     | 3.6     | V    |
 | Power Dissipation      | -              | -       | -       | 350     | mW   |
 | Standby Current        | No data signal | -       | -       | 1       | mA   |
 | Max LED Output Current | Per Channel    | -       | 18      | -       | mA   |

content/hardware/11.accessories/modulinos/modulino-pixels/tutorials/how-pixels-mp/content.md

@@ -75,7 +75,7 @@ Later in this article we teach how to [change the address](#how-to-change-i2c-ad
 
 ## Power Specifications
 
-The board is typically powered by +3.3 VDC when using the QWIIC interface as per the I²C standard. However, different power levels can be used when powering through the solderable pins, making this board compatible with both +3.3 and +5 VDC.
+The board is typically powered by +3.3 VDC when using the QWIIC interface as per the I²C standard.
 
 | Parameter              | Condition      | Minimum | Typical | Maximum | Unit |
 |------------------------|----------------|---------|---------|---------|------|

content/hardware/11.accessories/modulinos/modulino-thermo/tutorials/how-thermo-ardu/content.md

@@ -48,7 +48,7 @@ Depending on the board connected to the modulino, the I²C pin names to program
 
 ## Power Specifications
 
-The board is typically powered by +3.3 VDC when using the QWIIC interface as per the I²C standard. However, different power levels can be used when powering through the solderable pins, making this board compatible with both +3.3 and +5 VDC.
+The board is typically powered by +3.3 VDC when using the QWIIC interface as per the I²C standard.
 
 | Parameter       | Condition                                                         | Minimum | Typical     | Maximum | Unit |
 |-----------------|-------------------------------------------------------------------|---------|-------------|---------|------|

content/hardware/11.accessories/modulinos/modulino-thermo/tutorials/how-thermo-mp/content.md

@@ -48,7 +48,7 @@ Depending on the board connected to the modulino, the I²C pin names to program
 
 ## Power Specifications
 
-The board is typically powered by +3.3 VDC when using the QWIIC interface as per the I²C standard. However, different power levels can be used when powering through the solderable pins, making this board compatible with both +3.3 and +5 VDC.
+The board is typically powered by +3.3 VDC when using the QWIIC interface as per the I²C standard.
 
 | Parameter       | Condition                                                         | Minimum | Typical     | Maximum | Unit |
 |-----------------|-------------------------------------------------------------------|---------|-------------|---------|------|