Use Auto Format compatible bullet character in built-in example comment lists

per1234 · cmaglie · commit 4bff0331523d · 2017-07-18T11:07:37.000+02:00
Tools &gt; Auto Format in the Arduino IDE removes asterisks from the start of every line in a C style comment, causing that character to be unsuitable for use as a bullet for lists in the example comments.
diff --git a/examples/02.Digital/BlinkWithoutDelay/BlinkWithoutDelay.ino b/examples/02.Digital/BlinkWithoutDelay/BlinkWithoutDelay.ino
@@ -5,8 +5,8 @@
  can run at the same time without being interrupted by the LED code.
 
  The circuit:
- * Use the onboard LED.
- * Note: Most Arduinos have an on-board LED you can control. On the UNO, MEGA and ZERO 
+ - Use the onboard LED.
+ - Note: Most Arduinos have an on-board LED you can control. On the UNO, MEGA and ZERO 
   it is attached to digital pin 13, on MKR1000 on pin 6. LED_BUILTIN is set to
   the correct LED pin independent of which board is used.
   If you want to know what pin the on-board LED is connected to on your Arduino model, check
diff --git a/examples/02.Digital/Button/Button.ino b/examples/02.Digital/Button/Button.ino
@@ -6,11 +6,11 @@
 
 
  The circuit:
- * LED attached from pin 13 to ground
- * pushbutton attached to pin 2 from +5V
- * 10K resistor attached to pin 2 from ground
+ - LED attached from pin 13 to ground
+ - pushbutton attached to pin 2 from +5V
+ - 10K resistor attached to pin 2 from ground
 
- * Note: on most Arduinos there is already an LED on the board
+ - Note: on most Arduinos there is already an LED on the board
  attached to pin 13.
 
 
diff --git a/examples/02.Digital/Debounce/Debounce.ino b/examples/02.Digital/Debounce/Debounce.ino
@@ -7,11 +7,11 @@
  noise).
 
  The circuit:
- * LED attached from pin 13 to ground
- * pushbutton attached from pin 2 to +5V
- * 10K resistor attached from pin 2 to ground
+ - LED attached from pin 13 to ground
+ - pushbutton attached from pin 2 to +5V
+ - 10K resistor attached from pin 2 to ground
 
- * Note: On most Arduino boards, there is already an LED on the board
+ - Note: On most Arduino boards, there is already an LED on the board
  connected to pin 13, so you don't need any extra components for this example.
 
 
diff --git a/examples/02.Digital/DigitalInputPullup/DigitalInputPullup.ino b/examples/02.Digital/DigitalInputPullup/DigitalInputPullup.ino
@@ -5,8 +5,8 @@
  digital input on pin 2 and prints the results to the Serial Monitor.
 
  The circuit:
- * Momentary switch attached from pin 2 to ground
- * Built-in LED on pin 13
+ - Momentary switch attached from pin 2 to ground
+ - Built-in LED on pin 13
 
  Unlike pinMode(INPUT), there is no pull-down resistor necessary. An internal
  20K-ohm resistor is pulled to 5V. This configuration causes the input to
diff --git a/examples/02.Digital/StateChangeDetection/StateChangeDetection.ino b/examples/02.Digital/StateChangeDetection/StateChangeDetection.ino
@@ -10,9 +10,9 @@
  and on to off.
 
  The circuit:
- * pushbutton attached to pin 2 from +5V
- * 10K resistor attached to pin 2 from ground
- * LED attached from pin 13 to ground (or use the built-in LED on
+ - pushbutton attached to pin 2 from +5V
+ - 10K resistor attached to pin 2 from ground
+ - LED attached from pin 13 to ground (or use the built-in LED on
    most Arduino boards)
 
  created  27 Sep 2005
diff --git a/examples/02.Digital/toneKeyboard/toneKeyboard.ino b/examples/02.Digital/toneKeyboard/toneKeyboard.ino
@@ -4,9 +4,9 @@
  Plays a pitch that changes based on a changing analog input
 
  circuit:
- * 3 force-sensing resistors from +5V to analog in 0 through 5
- * 3 10K resistors from analog in 0 through 5 to ground
- * 8-ohm speaker on digital pin 8
+ - 3 force-sensing resistors from +5V to analog in 0 through 5
+ - 3 10K resistors from analog in 0 through 5 to ground
+ - 8-ohm speaker on digital pin 8
 
  created 21 Jan 2010
  modified 9 Apr 2012
diff --git a/examples/02.Digital/toneMelody/toneMelody.ino b/examples/02.Digital/toneMelody/toneMelody.ino
@@ -4,7 +4,7 @@
  Plays a melody
 
  circuit:
- * 8-ohm speaker on digital pin 8
+ - 8-ohm speaker on digital pin 8
 
  created 21 Jan 2010
  modified 30 Aug 2011
diff --git a/examples/02.Digital/toneMultiple/toneMultiple.ino b/examples/02.Digital/toneMultiple/toneMultiple.ino
@@ -4,7 +4,7 @@
  Plays multiple tones on multiple pins in sequence
 
  circuit:
- * 3 8-ohm speaker on digital pins 6, 7, and 8
+ - 3 8-ohm speaker on digital pins 6, 7, and 8
 
  created 8 March 2010
  by Tom Igoe
diff --git a/examples/02.Digital/tonePitchFollower/tonePitchFollower.ino b/examples/02.Digital/tonePitchFollower/tonePitchFollower.ino
@@ -4,9 +4,9 @@
  Plays a pitch that changes based on a changing analog input
 
  circuit:
- * 8-ohm speaker on digital pin 9
- * photoresistor on analog 0 to 5V
- * 4.7K resistor on analog 0 to ground
+ - 8-ohm speaker on digital pin 9
+ - photoresistor on analog 0 to 5V
+ - 4.7K resistor on analog 0 to ground
 
  created 21 Jan 2010
  modified 31 May 2012
diff --git a/examples/03.Analog/AnalogInOutSerial/AnalogInOutSerial.ino b/examples/03.Analog/AnalogInOutSerial/AnalogInOutSerial.ino
@@ -6,10 +6,10 @@
  Also prints the results to the Serial Monitor.
 
  The circuit:
- * potentiometer connected to analog pin 0.
+ - potentiometer connected to analog pin 0.
    Center pin of the potentiometer goes to the analog pin.
    side pins of the potentiometer go to +5V and ground
- * LED connected from digital pin 9 to ground
+ - LED connected from digital pin 9 to ground
 
  created 29 Dec. 2008
  modified 9 Apr 2012
diff --git a/examples/03.Analog/AnalogInput/AnalogInput.ino b/examples/03.Analog/AnalogInput/AnalogInput.ino
@@ -6,14 +6,14 @@
  the value obtained by analogRead().
 
  The circuit:
- * Potentiometer attached to analog input 0
- * center pin of the potentiometer to the analog pin
- * one side pin (either one) to ground
- * the other side pin to +5V
- * LED anode (long leg) attached to digital output 13
- * LED cathode (short leg) attached to ground
-
- * Note: because most Arduinos have a built-in LED attached
+ - Potentiometer attached to analog input 0
+ - center pin of the potentiometer to the analog pin
+ - one side pin (either one) to ground
+ - the other side pin to +5V
+ - LED anode (long leg) attached to digital output 13
+ - LED cathode (short leg) attached to ground
+
+ - Note: because most Arduinos have a built-in LED attached
  to pin 13 on the board, the LED is optional.
 
 
diff --git a/examples/03.Analog/AnalogWriteMega/AnalogWriteMega.ino b/examples/03.Analog/AnalogWriteMega/AnalogWriteMega.ino
@@ -5,7 +5,7 @@
   This sketch was written for the Arduino Mega, and will not work on other boards.
 
   The circuit:
-  * LEDs attached from pins 2 through 13 to ground.
+  - LEDs attached from pins 2 through 13 to ground.
 
   created 8 Feb 2009
   by Tom Igoe
diff --git a/examples/03.Analog/Calibration/Calibration.ino b/examples/03.Analog/Calibration/Calibration.ino
@@ -12,8 +12,8 @@
  maximum low and listen for anything higher as the new maximum.
 
  The circuit:
- * Analog sensor (potentiometer will do) attached to analog input 0
- * LED attached from digital pin 9 to ground
+ - Analog sensor (potentiometer will do) attached to analog input 0
+ - LED attached from digital pin 9 to ground
 
  created 29 Oct 2008
  By David A Mellis
diff --git a/examples/03.Analog/Fading/Fading.ino b/examples/03.Analog/Fading/Fading.ino
@@ -4,7 +4,7 @@
  This example shows how to fade an LED using the analogWrite() function.
 
  The circuit:
- * LED attached from digital pin 9 to ground.
+ - LED attached from digital pin 9 to ground.
 
  Created 1 Nov 2008
  By David A. Mellis
diff --git a/examples/03.Analog/Smoothing/Smoothing.ino b/examples/03.Analog/Smoothing/Smoothing.ino
@@ -7,7 +7,7 @@
   continually averages them.
 
   The circuit:
-    * Analog sensor (potentiometer will do) attached to analog input 0
+    - Analog sensor (potentiometer will do) attached to analog input 0
 
   Created 22 April 2007
   By David A. Mellis  <dam@mellis.org>
diff --git a/examples/04.Communication/ASCIITable/ASCIITable.ino b/examples/04.Communication/ASCIITable/ASCIITable.ino
@@ -2,8 +2,8 @@
   ASCII table
 
  Prints out byte values in all possible formats:
- * as raw binary values
- * as ASCII-encoded decimal, hex, octal, and binary values
+ - as raw binary values
+ - as ASCII-encoded decimal, hex, octal, and binary values
 
  For more on ASCII, see http://www.asciitable.com and http://en.wikipedia.org/wiki/ASCII
 
diff --git a/examples/04.Communication/Midi/Midi.ino b/examples/04.Communication/Midi/Midi.ino
@@ -7,9 +7,9 @@
 
 
  The circuit:
- * digital in 1 connected to MIDI jack pin 5
- * MIDI jack pin 2 connected to ground
- * MIDI jack pin 4 connected to +5V through 220-ohm resistor
+ - digital in 1 connected to MIDI jack pin 5
+ - MIDI jack pin 2 connected to ground
+ - MIDI jack pin 4 connected to +5V through 220-ohm resistor
  Attach a MIDI cable to the jack, then to a MIDI synth, and play music.
 
  created 13 Jun 2006
diff --git a/examples/04.Communication/MultiSerial/MultiSerial.ino b/examples/04.Communication/MultiSerial/MultiSerial.ino
@@ -7,8 +7,8 @@
  This example works only with boards with more than one serial like Arduino Mega, Due, Zero etc
 
  The circuit:
- * Any serial device attached to Serial port 1
- * Serial monitor open on Serial port 0:
+ - Any serial device attached to Serial port 1
+ - Serial monitor open on Serial port 0:
 
  created 30 Dec. 2008
  modified 20 May 2012
diff --git a/examples/04.Communication/PhysicalPixel/PhysicalPixel.ino b/examples/04.Communication/PhysicalPixel/PhysicalPixel.ino
@@ -11,7 +11,7 @@
  proxy), PD, or Max/MSP.
 
  The circuit:
- * LED connected from digital pin 13 to ground
+ - LED connected from digital pin 13 to ground
 
  created 2006
  by David A. Mellis
diff --git a/examples/04.Communication/ReadASCIIString/ReadASCIIString.ino b/examples/04.Communication/ReadASCIIString/ReadASCIIString.ino
@@ -6,10 +6,10 @@
  It parses them into ints, and uses those to fade an RGB LED.
 
  Circuit: Common-Cathode RGB LED wired like so:
- * Red anode: digital pin 3
- * Green anode: digital pin 5
- * Blue anode: digital pin 6
- * Cathode : GND
+ - Red anode: digital pin 3
+ - Green anode: digital pin 5
+ - Blue anode: digital pin 6
+ - Cathode : GND
 
  created 13 Apr 2012
  by Tom Igoe
diff --git a/examples/04.Communication/SerialCallResponse/SerialCallResponse.ino b/examples/04.Communication/SerialCallResponse/SerialCallResponse.ino
@@ -10,8 +10,8 @@
  Thanks to Greg Shakar and Scott Fitzgerald for the improvements
 
    The circuit:
- * potentiometers attached to analog inputs 0 and 1
- * pushbutton attached to digital I/O 2
+ - potentiometers attached to analog inputs 0 and 1
+ - pushbutton attached to digital I/O 2
 
  Created 26 Sept. 2005
  by Tom Igoe
diff --git a/examples/04.Communication/SerialCallResponseASCII/SerialCallResponseASCII.ino b/examples/04.Communication/SerialCallResponseASCII/SerialCallResponseASCII.ino
@@ -12,8 +12,8 @@
  Thanks to Greg Shakar and Scott Fitzgerald for the improvements
 
   The circuit:
- * potentiometers attached to analog inputs 0 and 1
- * pushbutton attached to digital I/O 2
+ - potentiometers attached to analog inputs 0 and 1
+ - pushbutton attached to digital I/O 2
 
 
 
diff --git a/examples/04.Communication/VirtualColorMixer/VirtualColorMixer.ino b/examples/04.Communication/VirtualColorMixer/VirtualColorMixer.ino
@@ -4,7 +4,7 @@
  take those three values and use them to change the background color of the screen.
 
  The circuit:
- * potentiometers attached to analog inputs 0, 1, and 2
+ - potentiometers attached to analog inputs 0, 1, and 2
 
  http://www.arduino.cc/en/Tutorial/VirtualColorMixer
 
diff --git a/examples/05.Control/Arrays/Arrays.ino b/examples/05.Control/Arrays/Arrays.ino
@@ -9,7 +9,7 @@
  contiguous, here the pins can be in any random order.
 
  The circuit:
- * LEDs from pins 2 through 7 to ground
+ - LEDs from pins 2 through 7 to ground
 
  created 2006
  by David A. Mellis
diff --git a/examples/05.Control/ForLoopIteration/ForLoopIteration.ino b/examples/05.Control/ForLoopIteration/ForLoopIteration.ino
@@ -5,7 +5,7 @@
  Lights multiple LEDs in sequence, then in reverse.
 
  The circuit:
- * LEDs from pins 2 through 7 to ground
+ - LEDs from pins 2 through 7 to ground
 
  created 2006
  by David A. Mellis
diff --git a/examples/05.Control/IfStatementConditional/IfStatementConditional.ino b/examples/05.Control/IfStatementConditional/IfStatementConditional.ino
@@ -7,12 +7,12 @@
  regardless of the level.
 
  The circuit:
- * potentiometer connected to analog pin 0.
+ - potentiometer connected to analog pin 0.
  Center pin of the potentiometer goes to the analog pin.
  side pins of the potentiometer go to +5V and ground
- * LED connected from digital pin 13 to ground
+ - LED connected from digital pin 13 to ground
 
- * Note: On most Arduino boards, there is already an LED on the board
+ - Note: On most Arduino boards, there is already an LED on the board
  connected to pin 13, so you don't need any extra components for this example.
 
  created 17 Jan 2009
diff --git a/examples/05.Control/WhileStatementConditional/WhileStatementConditional.ino b/examples/05.Control/WhileStatementConditional/WhileStatementConditional.ino
@@ -10,11 +10,11 @@
  This is a variation on the calibrate example.
 
  The circuit:
- * photoresistor connected from +5V to analog in pin 0
- * 10K resistor connected from ground to analog in pin 0
- * LED connected from digital pin 9 to ground through 220 ohm resistor
- * pushbutton attached from pin 2 to +5V
- * 10K resistor attached from pin 2 to ground
+ - photoresistor connected from +5V to analog in pin 0
+ - 10K resistor connected from ground to analog in pin 0
+ - LED connected from digital pin 9 to ground through 220 ohm resistor
+ - pushbutton attached from pin 2 to +5V
+ - 10K resistor attached from pin 2 to ground
 
  created 17 Jan 2009
  modified 30 Aug 2011
diff --git a/examples/05.Control/switchCase/switchCase.ino b/examples/05.Control/switchCase/switchCase.ino
@@ -10,8 +10,8 @@
  over the sensor.
 
  The circuit:
- * photoresistor from analog in 0 to +5V
- * 10K resistor from analog in 0 to ground
+ - photoresistor from analog in 0 to +5V
+ - 10K resistor from analog in 0 to ground
 
  created 1 Jul 2009
  modified 9 Apr 2012
diff --git a/examples/05.Control/switchCase2/switchCase2.ino b/examples/05.Control/switchCase2/switchCase2.ino
@@ -10,7 +10,7 @@
  the LEDs off.
 
  The circuit:
- * 5 LEDs attached to digital pins 2 through 6 through 220-ohm resistors
+ - 5 LEDs attached to digital pins 2 through 6 through 220-ohm resistors
 
  created 1 Jul 2009
  by Tom Igoe
diff --git a/examples/06.Sensors/Knock/Knock.ino b/examples/06.Sensors/Knock/Knock.ino
@@ -6,9 +6,9 @@
    "knock" to the serial port, and toggles the LED on pin 13.
 
    The circuit:
-	* + connection of the piezo attached to analog in 0
-	* - connection of the piezo attached to ground
-	* 1-megohm resistor attached from analog in 0 to ground
+	- + connection of the piezo attached to analog in 0
+	- - connection of the piezo attached to ground
+	- 1-megohm resistor attached from analog in 0 to ground
 
    http://www.arduino.cc/en/Tutorial/Knock
 
diff --git a/examples/06.Sensors/Memsic2125/Memsic2125.ino b/examples/06.Sensors/Memsic2125/Memsic2125.ino
@@ -7,10 +7,10 @@
    computer.
 
    The circuit:
-	* X output of accelerometer to digital pin 2
-	* Y output of accelerometer to digital pin 3
-	* +V of accelerometer to +5V
-	* GND of accelerometer to ground
+	- X output of accelerometer to digital pin 2
+	- Y output of accelerometer to digital pin 3
+	- +V of accelerometer to +5V
+	- GND of accelerometer to ground
 
    http://www.arduino.cc/en/Tutorial/Memsic2125
 
diff --git a/examples/06.Sensors/Ping/Ping.ino b/examples/06.Sensors/Ping/Ping.ino
@@ -7,9 +7,9 @@
    the distance of the object from the sensor.
 
    The circuit:
-	* +V connection of the PING))) attached to +5V
-	* GND connection of the PING))) attached to ground
-	* SIG connection of the PING))) attached to digital pin 7
+	- +V connection of the PING))) attached to +5V
+	- GND connection of the PING))) attached to ground
+	- SIG connection of the PING))) attached to digital pin 7
 
    http://www.arduino.cc/en/Tutorial/Ping
 
diff --git a/examples/07.Display/RowColumnScanning/RowColumnScanning.ino b/examples/07.Display/RowColumnScanning/RowColumnScanning.ino
diff --git a/examples/07.Display/barGraph/barGraph.ino b/examples/07.Display/barGraph/barGraph.ino
diff --git a/examples/09.USB/Keyboard/KeyboardLogout/KeyboardLogout.ino b/examples/09.USB/Keyboard/KeyboardLogout/KeyboardLogout.ino
diff --git a/examples/09.USB/Keyboard/KeyboardMessage/KeyboardMessage.ino b/examples/09.USB/Keyboard/KeyboardMessage/KeyboardMessage.ino
diff --git a/examples/09.USB/Keyboard/KeyboardReprogram/KeyboardReprogram.ino b/examples/09.USB/Keyboard/KeyboardReprogram/KeyboardReprogram.ino
diff --git a/examples/09.USB/Keyboard/KeyboardSerial/KeyboardSerial.ino b/examples/09.USB/Keyboard/KeyboardSerial/KeyboardSerial.ino
diff --git a/examples/09.USB/KeyboardAndMouseControl/KeyboardAndMouseControl.ino b/examples/09.USB/KeyboardAndMouseControl/KeyboardAndMouseControl.ino
diff --git a/examples/09.USB/Mouse/ButtonMouseControl/ButtonMouseControl.ino b/examples/09.USB/Mouse/ButtonMouseControl/ButtonMouseControl.ino
diff --git a/examples/09.USB/Mouse/JoystickMouseControl/JoystickMouseControl.ino b/examples/09.USB/Mouse/JoystickMouseControl/JoystickMouseControl.ino
