Merge branch 'fine-tune-flow-control-and-speed-configurations-in-microchip-ksz8xxx-dsa-driver'

Oleksij Rempel says:

====================
Fine-Tune Flow Control and Speed Configurations in Microchip KSZ8xxx DSA Driver

This patch set focuses on enhancing the configurability of flow
control, speed, and duplex settings in the Microchip KSZ8xxx DSA driver.

The first patch allows more granular control over the CPU port's flow
control, speed, and duplex settings. The second patch introduces a
method for port configurations for port with integrated PHYs, primarily
concerning flow control based on duplex mode.
====================

Link: https://lore.kernel.org/r/20231127145101.3039399-1-o.rempel@pengutronix.de
Signed-off-by: Jakub Kicinski <kuba@kernel.org>

Author: kuba-moo

drivers/net/dsa/microchip/ksz8.h

@@ -56,5 +56,9 @@ int ksz8_reset_switch(struct ksz_device *dev);
 int ksz8_switch_init(struct ksz_device *dev);
 void ksz8_switch_exit(struct ksz_device *dev);
 int ksz8_change_mtu(struct ksz_device *dev, int port, int mtu);
+void ksz8_phylink_mac_link_up(struct ksz_device *dev, int port,
+			      unsigned int mode, phy_interface_t interface,
+			      struct phy_device *phydev, int speed, int duplex,
+			      bool tx_pause, bool rx_pause);
 
 #endif

drivers/net/dsa/microchip/ksz8795.c

@@ -1439,6 +1439,127 @@ void ksz8_config_cpu_port(struct dsa_switch *ds)
 	}
 }
 
+/**
+ * ksz8_phy_port_link_up - Configures ports with integrated PHYs
+ * @dev: The KSZ device instance.
+ * @port: The port number to configure.
+ * @duplex: The desired duplex mode.
+ * @tx_pause: If true, enables transmit pause.
+ * @rx_pause: If true, enables receive pause.
+ *
+ * Description:
+ * The function configures flow control settings for a given port based on the
+ * desired settings and current duplex mode.
+ *
+ * According to the KSZ8873 datasheet, the PORT_FORCE_FLOW_CTRL bit in the
+ * Port Control 2 register (0x1A for Port 1, 0x22 for Port 2, 0x32 for Port 3)
+ * determines how flow control is handled on the port:
+ *    "1 = will always enable full-duplex flow control on the port, regardless
+ *         of AN result.
+ *     0 = full-duplex flow control is enabled based on AN result."
+ *
+ * This means that the flow control behavior depends on the state of this bit:
+ * - If PORT_FORCE_FLOW_CTRL is set to 1, the switch will ignore AN results and
+ *   force flow control on the port.
+ * - If PORT_FORCE_FLOW_CTRL is set to 0, the switch will enable or disable
+ *   flow control based on the AN results.
+ *
+ * However, there is a potential limitation in this configuration. It is
+ * currently not possible to force disable flow control on a port if we still
+ * advertise pause support. While such a configuration is not currently
+ * supported by Linux, and may not make practical sense, it's important to be
+ * aware of this limitation when working with the KSZ8873 and similar devices.
+ */
+static void ksz8_phy_port_link_up(struct ksz_device *dev, int port, int duplex,
+				  bool tx_pause, bool rx_pause)
+{
+	const u16 *regs = dev->info->regs;
+	u8 sctrl = 0;
+
+	/* The KSZ8795 switch differs from the KSZ8873 by supporting
+	 * asymmetric pause control. However, since a single bit is used to
+	 * control both RX and TX pause, we can't enforce asymmetric pause
+	 * control - both TX and RX pause will be either enabled or disabled
+	 * together.
+	 *
+	 * If auto-negotiation is enabled, we usually allow the flow control to
+	 * be determined by the auto-negotiation process based on the
+	 * capabilities of both link partners. However, for KSZ8873, the
+	 * PORT_FORCE_FLOW_CTRL bit may be set by the hardware bootstrap,
+	 * ignoring the auto-negotiation result. Thus, even in auto-negotiation
+	 * mode, we need to ensure that the PORT_FORCE_FLOW_CTRL bit is
+	 * properly cleared.
+	 *
+	 * In the absence of pause auto-negotiation, we will enforce symmetric
+	 * pause control for both variants of switches - KSZ8873 and KSZ8795.
+	 *
+	 * Autoneg Pause Autoneg      rx,tx	PORT_FORCE_FLOW_CTRL
+	 * 1		1		x	0
+	 * 0		1		x	0 (flow control probably disabled)
+	 * x		0		1	1 (flow control force enabled)
+	 * 1		0		0	0 (flow control still depends on
+	 *					   aneg result due to hardware)
+	 * 0		0		0	0 (flow control probably disabled)
+	 */
+	if (dev->ports[port].manual_flow && tx_pause)
+		sctrl |= PORT_FORCE_FLOW_CTRL;
+
+	ksz_prmw8(dev, port, regs[P_STP_CTRL], PORT_FORCE_FLOW_CTRL, sctrl);
+}
+
+/**
+ * ksz8_cpu_port_link_up - Configures the CPU port of the switch.
+ * @dev: The KSZ device instance.
+ * @speed: The desired link speed.
+ * @duplex: The desired duplex mode.
+ * @tx_pause: If true, enables transmit pause.
+ * @rx_pause: If true, enables receive pause.
+ *
+ * Description:
+ * The function configures flow control and speed settings for the CPU
+ * port of the switch based on the desired settings, current duplex mode, and
+ * speed.
+ */
+static void ksz8_cpu_port_link_up(struct ksz_device *dev, int speed, int duplex,
+				  bool tx_pause, bool rx_pause)
+{
+	const u16 *regs = dev->info->regs;
+	u8 ctrl = 0;
+
+	/* SW_FLOW_CTRL, SW_HALF_DUPLEX, and SW_10_MBIT bits are bootstrappable
+	 * at least on KSZ8873. They can have different values depending on your
+	 * board setup.
+	 */
+	if (tx_pause || rx_pause)
+		ctrl |= SW_FLOW_CTRL;
+
+	if (duplex == DUPLEX_HALF)
+		ctrl |= SW_HALF_DUPLEX;
+
+	/* This hardware only supports SPEED_10 and SPEED_100. For SPEED_10
+	 * we need to set the SW_10_MBIT bit. Otherwise, we can leave it 0.
+	 */
+	if (speed == SPEED_10)
+		ctrl |= SW_10_MBIT;
+
+	ksz_rmw8(dev, regs[S_BROADCAST_CTRL], SW_HALF_DUPLEX | SW_FLOW_CTRL |
+		 SW_10_MBIT, ctrl);
+}
+
+void ksz8_phylink_mac_link_up(struct ksz_device *dev, int port,
+			      unsigned int mode, phy_interface_t interface,
+			      struct phy_device *phydev, int speed, int duplex,
+			      bool tx_pause, bool rx_pause)
+{
+	/* If the port is the CPU port, apply special handling. Only the CPU
+	 * port is configured via global registers.
+	 */
+	if (dev->cpu_port == port)
+		ksz8_cpu_port_link_up(dev, speed, duplex, tx_pause, rx_pause);
+	else if (dev->info->internal_phy[port])
+		ksz8_phy_port_link_up(dev, port, duplex, tx_pause, rx_pause);
+}
+
 static int ksz8_handle_global_errata(struct dsa_switch *ds)
 {
 	struct ksz_device *dev = ds->priv;
@@ -1487,8 +1608,6 @@ int ksz8_setup(struct dsa_switch *ds)
 	 */
 	ds->vlan_filtering_is_global = true;
 
-	ksz_cfg(dev, S_REPLACE_VID_CTRL, SW_FLOW_CTRL, true);
-
 	/* Enable automatic fast aging when link changed detected. */
 	ksz_cfg(dev, S_LINK_AGING_CTRL, SW_LINK_AUTO_AGING, true);
 

drivers/net/dsa/microchip/ksz_common.c

@@ -277,6 +277,7 @@ static const struct ksz_dev_ops ksz8_dev_ops = {
 	.mirror_add = ksz8_port_mirror_add,
 	.mirror_del = ksz8_port_mirror_del,
 	.get_caps = ksz8_get_caps,
+	.phylink_mac_link_up = ksz8_phylink_mac_link_up,
 	.config_cpu_port = ksz8_config_cpu_port,
 	.enable_stp_addr = ksz8_enable_stp_addr,
 	.reset = ksz8_reset_switch,
@@ -2966,8 +2967,10 @@ static void ksz_phylink_mac_config(struct dsa_switch *ds, int port,
 {
 	struct ksz_device *dev = ds->priv;
 
-	if (ksz_is_ksz88x3(dev))
+	if (ksz_is_ksz88x3(dev)) {
+		dev->ports[port].manual_flow = !(state->pause & MLO_PAUSE_AN);
 		return;
+	}
 
 	/* Internal PHYs */
 	if (dev->info->internal_phy[port])
@@ -3110,10 +3113,8 @@ static void ksz_phylink_mac_link_up(struct dsa_switch *ds, int port,
 {
 	struct ksz_device *dev = ds->priv;
 
-	if (dev->dev_ops->phylink_mac_link_up)
-		dev->dev_ops->phylink_mac_link_up(dev, port, mode, interface,
-						  phydev, speed, duplex,
-						  tx_pause, rx_pause);
+	dev->dev_ops->phylink_mac_link_up(dev, port, mode, interface, phydev,
+					  speed, duplex, tx_pause, rx_pause);
 }
 
 static int ksz_switch_detect(struct ksz_device *dev)

drivers/net/dsa/microchip/ksz_common.h

@@ -134,6 +134,7 @@ struct ksz_port {
 	ktime_t tstamp_msg;
 	struct completion tstamp_msg_comp;
 #endif
+	bool manual_flow;
 };
 
 struct ksz_device {