Merge tag 'i2c-for-6.13-rc1' of git://git.kernel.org/pub/scm/linux/kernel/git/wsa/linux

Pull i2c updates from Wolfram Sang:
 "Core:

   - drivers can now use a GPIO as a side channel for SMBus Alerts using
     a generic binding

   - regular stuff like mem leak fix, Makefile maintenance...

  Host improvements and refactoring:

   - All controllers using the 'remove_new' callback have been reverted
     to use the 'remove' callback

   - Intel SCH controller underwent significant refactoring, this brings
     love and a modern look to the driver

   - PIIX4 driver refactored to enable usage by other drivers (e.g., AMD
     ASF)

   - iMX/MXC improved message handling to reduce protocol overhead:
     Refactored DMA/non-DMA read/write and bus polling mechanisms to
     achieve this.

   - ACPI documentation for PIIX4

  New host features:

   - i2c-cadence support for atomic transfers

   - Qualcomm CII support for a 32MHz serial engine clock

  Deprecated features:

   - Dropped outdated support for AMD756 S4882 and NFORCE2 S4985. If
     somebody misses this, Jean will rewrite support using the proper
     i2c mux framework.

  New hardware IDs for existing drivers:

   - Intel Panther Lake

   - S32G2/S32G3 SoCs

   - HJMC01 DesignWare ACPI HID

   - PIC64GX to Microchip Core

   - Qualcomm SDM670 to Qualcomm CCI

  New drivers:

   - AMD ASF

   - Realtek RTL I2C Controller

  at24 updates:

   - add support for the lockable page on ST M24256E"

* tag 'i2c-for-6.13-rc1' of git://git.kernel.org/pub/scm/linux/kernel/git/wsa/linux: (59 commits)
  docs: i2c: piix4: Add ACPI section
  i2c: Add driver for the RTL9300 I2C controller
  i2c: qcom-cci: Remove unused struct member cci_clk_rate
  dt-bindings: i2c: Add Realtek RTL I2C Controller
  i2c: busses: Use *-y instead of *-objs in Makefile
  i2c: imx: add support for S32G2/S32G3 SoCs
  dt-bindings: i2c: imx: add SoC specific compatible strings for S32G
  i2c: qcom-cci: Remove the unused variable cci_clk_rate
  i2c: Drop legacy muxing pseudo-drivers
  i2c: imx: prevent rescheduling in non dma mode
  i2c: imx: separate atomic, dma and non-dma use case
  i2c: imx: do not poll for bus busy in single master mode
  i2c: designware: Add a new ACPI HID for HJMC01 I2C controller
  i2c: qcom-geni: Keep comment why interrupts start disabled
  dt-bindings: i2c: microchip: corei2c: Add PIC64GX as compatible with driver
  i2c: designware: constify abort_sources
  i2c: Switch back to struct platform_driver::remove()
  i2c: qcom-geni: Support systems with 32MHz serial engine clock
  i2c: qcom-cci: Stop complaining about DT set clock rate
  dt-bindings: i2c: qcom-cci: Document SDM670 compatible
  ...

Author: torvalds

Documentation/devicetree/bindings/eeprom/at24.yaml

@@ -141,6 +141,8 @@ properties:
           - const: microchip,24aa025e48
       - items:
           - const: microchip,24aa025e64
+      - items:
+          - const: st,24256e-wl
       - pattern: '^atmel,24c(32|64)d-wl$' # Actual vendor is st
 
   label:

Documentation/devicetree/bindings/i2c/i2c-imx.yaml

@@ -18,6 +18,7 @@ properties:
       - const: fsl,imx1-i2c
       - const: fsl,imx21-i2c
       - const: fsl,vf610-i2c
+      - const: nxp,s32g2-i2c
       - items:
           - enum:
               - fsl,ls1012a-i2c
@@ -54,6 +55,9 @@ properties:
               - fsl,imx8mn-i2c
               - fsl,imx8mp-i2c
           - const: fsl,imx21-i2c
+      - items:
+          - const: nxp,s32g3-i2c
+          - const: nxp,s32g2-i2c
 
   reg:
     maxItems: 1

Documentation/devicetree/bindings/i2c/microchip,corei2c.yaml

@@ -16,7 +16,9 @@ properties:
   compatible:
     oneOf:
       - items:
-          - const: microchip,mpfs-i2c # Microchip PolarFire SoC compatible SoCs
+          - enum:
+              - microchip,pic64gx-i2c
+              - microchip,mpfs-i2c # Microchip PolarFire SoC compatible SoCs
           - const: microchip,corei2c-rtl-v7 # Microchip Fabric based i2c IP core
       - const: microchip,corei2c-rtl-v7 # Microchip Fabric based i2c IP core
 

Documentation/devicetree/bindings/i2c/qcom,i2c-cci.yaml

@@ -27,6 +27,7 @@ properties:
           - enum:
               - qcom,sc7280-cci
               - qcom,sc8280xp-cci
+              - qcom,sdm670-cci
               - qcom,sdm845-cci
               - qcom,sm6350-cci
               - qcom,sm8250-cci
@@ -139,6 +140,24 @@ allOf:
             - const: cci
             - const: camss_ahb
 
+  - if:
+      properties:
+        compatible:
+          contains:
+            enum:
+              - qcom,sdm670-cci
+    then:
+      properties:
+        clocks:
+          minItems: 4
+          maxItems: 4
+        clock-names:
+          items:
+            - const: camnoc_axi
+            - const: soc_ahb
+            - const: cpas_ahb
+            - const: cci
+
   - if:
       properties:
         compatible:

Documentation/devicetree/bindings/i2c/realtek,rtl9301-i2c.yaml

@@ -0,0 +1,69 @@
+# SPDX-License-Identifier: (GPL-2.0-only OR BSD-2-Clause)
+%YAML 1.2
+---
+$id: http://devicetree.org/schemas/i2c/realtek,rtl9301-i2c.yaml#
+$schema: http://devicetree.org/meta-schemas/core.yaml#
+
+title: Realtek RTL I2C Controller
+
+maintainers:
+  - Chris Packham <chris.packham@alliedtelesis.co.nz>
+
+description:
+  The RTL9300 SoC has two I2C controllers. Each of these has an SCL line (which
+  if not-used for SCL can be a GPIO). There are 8 common SDA lines that can be
+  assigned to either I2C controller.
+
+properties:
+  compatible:
+    oneOf:
+      - items:
+          - enum:
+              - realtek,rtl9302b-i2c
+              - realtek,rtl9302c-i2c
+              - realtek,rtl9303-i2c
+          - const: realtek,rtl9301-i2c
+      - const: realtek,rtl9301-i2c
+
+  reg:
+    description: Register offset and size this I2C controller.
+
+  "#address-cells":
+    const: 1
+
+  "#size-cells":
+    const: 0
+
+patternProperties:
+  '^i2c@[0-7]$':
+    $ref: /schemas/i2c/i2c-controller.yaml
+    unevaluatedProperties: false
+
+    properties:
+      reg:
+        description: The SDA pin associated with the I2C bus.
+        maxItems: 1
+
+    required:
+      - reg
+
+required:
+  - compatible
+  - reg
+
+additionalProperties: false
+
+examples:
+  - |
+    i2c@36c {
+      compatible = "realtek,rtl9301-i2c";
+      reg = <0x36c 0x14>;
+      #address-cells = <1>;
+      #size-cells = <0>;
+
+      i2c@2 {
+        reg = <2>;
+        #address-cells = <1>;
+        #size-cells = <0>;
+      };
+    };

Documentation/i2c/busses/i2c-i801.rst

@@ -49,6 +49,7 @@ Supported adapters:
   * Intel Meteor Lake (SOC and PCH)
   * Intel Birch Stream (SOC)
   * Intel Arrow Lake (SOC)
+  * Intel Panther Lake (SOC)
 
    Datasheets: Publicly available at the Intel website
 

Documentation/i2c/busses/i2c-piix4.rst

@@ -109,3 +109,66 @@ which can easily get corrupted due to a state machine bug. These are mostly
 Thinkpad laptops, but desktop systems may also be affected. We have no list
 of all affected systems, so the only safe solution was to prevent access to
 the SMBus on all IBM systems (detected using DMI data.)
+
+
+Description in the ACPI code
+----------------------------
+
+Device driver for the PIIX4 chip creates a separate I2C bus for each of its
+ports::
+
+    $ i2cdetect -l
+    ...
+    i2c-7   unknown         SMBus PIIX4 adapter port 0 at 0b00      N/A
+    i2c-8   unknown         SMBus PIIX4 adapter port 2 at 0b00      N/A
+    i2c-9   unknown         SMBus PIIX4 adapter port 1 at 0b20      N/A
+    ...
+
+Therefore if you want to access one of these busses in the ACPI code, port
+subdevices are needed to be declared inside the PIIX device::
+
+    Scope (\_SB_.PCI0.SMBS)
+    {
+        Name (_ADR, 0x00140000)
+
+        Device (SMB0) {
+            Name (_ADR, 0)
+        }
+        Device (SMB1) {
+            Name (_ADR, 1)
+        }
+        Device (SMB2) {
+            Name (_ADR, 2)
+        }
+    }
+
+If this is not the case for your UEFI firmware and you don't have access to the
+source code, you can use ACPI SSDT Overlays to provide the missing parts. Just
+keep in mind that in this case you would need to load your extra SSDT table
+before the piix4 driver starts, i.e. you should provide SSDT via initrd or EFI
+variable methods and not via configfs.
+
+As an example of usage here is the ACPI snippet code that would assign jc42
+driver to the 0x1C device on the I2C bus created by the PIIX port 0::
+
+    Device (JC42) {
+        Name (_HID, "PRP0001")
+        Name (_DDN, "JC42 Temperature sensor")
+        Name (_CRS, ResourceTemplate () {
+            I2cSerialBusV2 (
+                0x001c,
+                ControllerInitiated,
+                100000,
+                AddressingMode7Bit,
+                "\\_SB.PCI0.SMBS.SMB0",
+                0
+            )
+        })
+
+        Name (_DSD, Package () {
+            ToUUID("daffd814-6eba-4d8c-8a91-bc9bbf4aa301"),
+            Package () {
+                Package () { "compatible", Package() { "jedec,jc-42.4-temp" } },
+            }
+        })
+    }

Documentation/i2c/writing-clients.rst

@@ -31,12 +31,11 @@ driver model device node, and its I2C address.
 
 ::
 
-  static struct i2c_device_id foo_idtable[] = {
+  static const struct i2c_device_id foo_idtable[] = {
 	{ "foo", my_id_for_foo },
 	{ "bar", my_id_for_bar },
 	{ }
   };
-
   MODULE_DEVICE_TABLE(i2c, foo_idtable);
 
   static struct i2c_driver foo_driver = {

MAINTAINERS

@@ -1115,6 +1115,12 @@ L:	linux-i2c@vger.kernel.org
 S:	Maintained
 F:	drivers/i2c/busses/i2c-amd-mp2*
 
+AMD ASF I2C DRIVER
+M:	Shyam Sundar S K <shyam-sundar.s-k@amd.com>
+L:	linux-i2c@vger.kernel.org
+S:	Supported
+F:	drivers/i2c/busses/i2c-amd-asf-plat.c
+
 AMD PDS CORE DRIVER
 M:	Shannon Nelson <shannon.nelson@amd.com>
 M:	Brett Creeley <brett.creeley@amd.com>
@@ -10750,14 +10756,12 @@ F:	Documentation/i2c/busses/i2c-viapro.rst
 F:	drivers/i2c/busses/i2c-ali1535.c
 F:	drivers/i2c/busses/i2c-ali1563.c
 F:	drivers/i2c/busses/i2c-ali15x3.c
-F:	drivers/i2c/busses/i2c-amd756-s4882.c
 F:	drivers/i2c/busses/i2c-amd756.c
 F:	drivers/i2c/busses/i2c-amd8111.c
 F:	drivers/i2c/busses/i2c-i801.c
 F:	drivers/i2c/busses/i2c-isch.c
-F:	drivers/i2c/busses/i2c-nforce2-s4985.c
 F:	drivers/i2c/busses/i2c-nforce2.c
-F:	drivers/i2c/busses/i2c-piix4.c
+F:	drivers/i2c/busses/i2c-piix4.*
 F:	drivers/i2c/busses/i2c-sis5595.c
 F:	drivers/i2c/busses/i2c-sis630.c
 F:	drivers/i2c/busses/i2c-sis96x.c
@@ -20218,6 +20222,13 @@ S:	Maintained
 T:	git https://github.com/pkshih/rtw.git
 F:	drivers/net/wireless/realtek/rtl8xxxu/
 
+RTL9300 I2C DRIVER (rtl9300-i2c)
+M:	Chris Packham <chris.packham@alliedtelesis.co.nz>
+L:	linux-i2c@vger.kernel.org
+S:	Maintained
+F:	Documentation/devicetree/bindings/i2c/realtek,rtl9301-i2c.yaml
+F:	drivers/i2c/busses/i2c-rtl9300.c
+
 RTRS TRANSPORT DRIVERS
 M:	Md. Haris Iqbal <haris.iqbal@ionos.com>
 M:	Jack Wang <jinpu.wang@ionos.com>

drivers/i2c/Makefile

@@ -5,10 +5,10 @@
 
 obj-$(CONFIG_I2C_BOARDINFO)	+= i2c-boardinfo.o
 obj-$(CONFIG_I2C)		+= i2c-core.o
-i2c-core-objs 			:= i2c-core-base.o i2c-core-smbus.o
+i2c-core-y			:= i2c-core-base.o i2c-core-smbus.o
 i2c-core-$(CONFIG_ACPI)		+= i2c-core-acpi.o
-i2c-core-$(CONFIG_I2C_SLAVE) 	+= i2c-core-slave.o
-i2c-core-$(CONFIG_OF) 		+= i2c-core-of.o
+i2c-core-$(CONFIG_I2C_SLAVE)	+= i2c-core-slave.o
+i2c-core-$(CONFIG_OF)		+= i2c-core-of.o
 
 obj-$(CONFIG_I2C_SMBUS)		+= i2c-smbus.o
 obj-$(CONFIG_I2C_CHARDEV)	+= i2c-dev.o