Merge branch 'pci/misc'

- Reorder struct pci_dev to avoid holes and reduce size (Christophe
  JAILLET)

- Change pdev->rom_attr_enabled to single bit since it's only a boolean
  value (Christophe JAILLET)

- Use struct_size() in pirq_convert_irt_table() instead of hand-writing it
  (Christophe JAILLET)

- Explicitly include correct DT includes to untangle headers (Rob Herring)

- Fix a DOE race between destroy_work_on_stack() and the stack-allocated
  task->work struct going out of scope in pci_doe() (Ira Weiny)

- Use pci_dev_id() when possible instead of manually composing ID from
  dev->bus->number and dev->devfn (Xiongfeng Wang, Zheng Zengkai)

- Move pci_create_resource_files() declarations to linux/pci.h for alpha
  build warnings (Arnd Bergmann)

- Remove unused hotplug function declarations (Yue Haibing)

- Remove unused mvebu struct mvebu_pcie.busn (Pali Rohár)

- Unexport pcie_port_bus_type (Bjorn Helgaas)

- Remove unnecessary sysfs ID local variable initialization (Bjorn Helgaas)

- Fix BAR value printk formatting to accommodate 32-bit values (Bjorn
  Helgaas)

- Use consistent pointer types for config access syscall get_user() and
  put_user() uses (Bjorn Helgaas)

- Simplify AER_RECOVER_RING_SIZE definition (Bjorn Helgaas)

- Simplify pci_pio_to_address() (Bjorn Helgaas)

- Simplify pci_dev_driver() (Bjorn Helgaas)

- Fix pci_bus_resetable(), pci_slot_resetable() name typos (Bjorn Helgaas)

- Fix code and doc typos and code formatting (Bjorn Helgaas)

- Tidy config space save/restore messages (Bjorn Helgaas)

* pci/misc:
  PCI: Tidy config space save/restore messages
  PCI: Fix code formatting inconsistencies
  PCI: Fix typos in docs and comments
  PCI: Fix pci_bus_resetable(), pci_slot_resetable() name typos
  PCI: Simplify pci_dev_driver()
  PCI: Simplify pci_pio_to_address()
  PCI/AER: Simplify AER_RECOVER_RING_SIZE definition
  PCI: Use consistent put_user() pointer types
  PCI: Fix printk field formatting
  PCI: Remove unnecessary initializations
  PCI: Unexport pcie_port_bus_type
  PCI: mvebu: Remove unused busn member
  PCI: Remove unused function declarations
  PCI/sysfs: Move declarations to linux/pci.h
  PCI/P2PDMA: Use pci_dev_id() to simplify the code
  PCI/IOV: Use pci_dev_id() to simplify the code
  PCI/AER: Use pci_dev_id() to simplify the code
  PCI: apple: Use pci_dev_id() to simplify the code
  PCI/DOE: Fix destroy_work_on_stack() race
  PCI: Explicitly include correct DT includes
  x86/PCI: Use struct_size() in pirq_convert_irt_table()
  PCI: Change pdev->rom_attr_enabled to single bit
  PCI: Reorder pci_dev fields to reduce holes

Author: bjorn-helgaas

Documentation/PCI/pci-error-recovery.rst

@@ -17,7 +17,7 @@ chipsets are able to deal with these errors; these include PCI-E chipsets,
 and the PCI-host bridges found on IBM Power4, Power5 and Power6-based
 pSeries boxes. A typical action taken is to disconnect the affected device,
 halting all I/O to it.  The goal of a disconnection is to avoid system
-corruption; for example, to halt system memory corruption due to DMA's
+corruption; for example, to halt system memory corruption due to DMAs
 to "wild" addresses. Typically, a reconnection mechanism is also
 offered, so that the affected PCI device(s) are reset and put back
 into working condition. The reset phase requires coordination
@@ -178,9 +178,9 @@ is STEP 6 (Permanent Failure).
    complex and not worth implementing.
 
    The current powerpc implementation doesn't much care if the device
-   attempts I/O at this point, or not.  I/O's will fail, returning
+   attempts I/O at this point, or not.  I/Os will fail, returning
    a value of 0xff on read, and writes will be dropped. If more than
-   EEH_MAX_FAILS I/O's are attempted to a frozen adapter, EEH
+   EEH_MAX_FAILS I/Os are attempted to a frozen adapter, EEH
    assumes that the device driver has gone into an infinite loop
    and prints an error to syslog.  A reboot is then required to
    get the device working again.
@@ -204,7 +204,7 @@ instead will have gone directly to STEP 3 (Link Reset) or STEP 4 (Slot Reset)
 .. note::
 
    The following is proposed; no platform implements this yet:
-   Proposal: All I/O's should be done _synchronously_ from within
+   Proposal: All I/Os should be done _synchronously_ from within
    this callback, errors triggered by them will be returned via
    the normal pci_check_whatever() API, no new error_detected()
    callback will be issued due to an error happening here. However,
@@ -258,7 +258,7 @@ Powerpc platforms implement two levels of slot reset:
 soft reset(default) and fundamental(optional) reset.
 
 Powerpc soft reset consists of asserting the adapter #RST line and then
-restoring the PCI BAR's and PCI configuration header to a state
+restoring the PCI BARs and PCI configuration header to a state
 that is equivalent to what it would be after a fresh system
 power-on followed by power-on BIOS/system firmware initialization.
 Soft reset is also known as hot-reset.
@@ -362,7 +362,7 @@ permanent failure in some way.  If the device is hotplug-capable,
 the operator will probably want to remove and replace the device.
 Note, however, not all failures are truly "permanent". Some are
 caused by over-heating, some by a poorly seated card. Many
-PCI error events are caused by software bugs, e.g. DMA's to
+PCI error events are caused by software bugs, e.g. DMAs to
 wild addresses or bogus split transactions due to programming
 errors. See the discussion in Documentation/powerpc/eeh-pci-error-recovery.rst
 for additional detail on real-life experience of the causes of

arch/alpha/include/asm/pci.h

@@ -88,7 +88,4 @@ extern void pci_adjust_legacy_attr(struct pci_bus *bus,
 				   enum pci_mmap_state mmap_type);
 #define HAVE_PCI_LEGACY	1
 
-extern int pci_create_resource_files(struct pci_dev *dev);
-extern void pci_remove_resource_files(struct pci_dev *dev);
-
 #endif /* __ALPHA_PCI_H */

arch/x86/pci/irq.c

@@ -136,14 +136,14 @@ static inline struct irq_routing_table *pirq_convert_irt_table(u8 *addr,
 	if (ir->signature != IRT_SIGNATURE || !ir->used || ir->size < ir->used)
 		return NULL;
 
-	size = sizeof(*ir) + ir->used * sizeof(ir->slots[0]);
+	size = struct_size(ir, slots, ir->used);
 	if (size > limit - addr)
 		return NULL;
 
 	DBG(KERN_DEBUG "PCI: $IRT Interrupt Routing Table found at 0x%lx\n",
 	    __pa(ir));
 
-	size = sizeof(*rt) + ir->used * sizeof(rt->slots[0]);
+	size = struct_size(rt, slots, ir->used);
 	rt = kzalloc(size, GFP_KERNEL);
 	if (!rt)
 		return NULL;

drivers/pci/controller/cadence/pci-j721e.c

@@ -14,8 +14,8 @@
 #include <linux/irqdomain.h>
 #include <linux/mfd/syscon.h>
 #include <linux/of.h>
-#include <linux/of_device.h>
 #include <linux/pci.h>
+#include <linux/platform_device.h>
 #include <linux/pm_runtime.h>
 #include <linux/regmap.h>
 

drivers/pci/controller/cadence/pcie-cadence-plat.c

@@ -6,11 +6,10 @@
  * Author: Tom Joseph <tjoseph@cadence.com>
  */
 #include <linux/kernel.h>
-#include <linux/of_address.h>
+#include <linux/of.h>
 #include <linux/of_pci.h>
 #include <linux/platform_device.h>
 #include <linux/pm_runtime.h>
-#include <linux/of_device.h>
 #include "pcie-cadence.h"
 
 #define CDNS_PLAT_CPU_TO_BUS_ADDR	0x0FFFFFFF

drivers/pci/controller/cadence/pcie-cadence.c

@@ -4,6 +4,7 @@
 // Author: Cyrille Pitchen <cyrille.pitchen@free-electrons.com>
 
 #include <linux/kernel.h>
+#include <linux/of.h>
 
 #include "pcie-cadence.h"
 

drivers/pci/controller/cadence/pcie-cadence.h

@@ -32,7 +32,7 @@
 #define  CDNS_PCIE_LM_ID_SUBSYS(sub) \
 	(((sub) << CDNS_PCIE_LM_ID_SUBSYS_SHIFT) & CDNS_PCIE_LM_ID_SUBSYS_MASK)
 
-/* Root Port Requestor ID Register */
+/* Root Port Requester ID Register */
 #define CDNS_PCIE_LM_RP_RID	(CDNS_PCIE_LM_BASE + 0x0228)
 #define  CDNS_PCIE_LM_RP_RID_MASK	GENMASK(15, 0)
 #define  CDNS_PCIE_LM_RP_RID_SHIFT	0

drivers/pci/controller/dwc/pci-dra7xx.c

@@ -16,7 +16,7 @@
 #include <linux/irqdomain.h>
 #include <linux/kernel.h>
 #include <linux/module.h>
-#include <linux/of_device.h>
+#include <linux/of.h>
 #include <linux/of_gpio.h>
 #include <linux/of_pci.h>
 #include <linux/pci.h>

drivers/pci/controller/dwc/pci-exynos.c

@@ -14,11 +14,11 @@
 #include <linux/interrupt.h>
 #include <linux/kernel.h>
 #include <linux/init.h>
-#include <linux/of_device.h>
 #include <linux/pci.h>
 #include <linux/platform_device.h>
 #include <linux/phy/phy.h>
 #include <linux/regulator/consumer.h>
+#include <linux/mod_devicetable.h>
 #include <linux/module.h>
 
 #include "pcie-designware.h"

drivers/pci/controller/dwc/pci-imx6.c

@@ -17,8 +17,8 @@
 #include <linux/mfd/syscon/imx6q-iomuxc-gpr.h>
 #include <linux/mfd/syscon/imx7-iomuxc-gpr.h>
 #include <linux/module.h>
+#include <linux/of.h>
 #include <linux/of_gpio.h>
-#include <linux/of_device.h>
 #include <linux/of_address.h>
 #include <linux/pci.h>
 #include <linux/platform_device.h>